Elmer fudd full#
Elmer fudd series#

Elmer fudd series#

Last year, the revival series Looney Tunes Cartoons premiered on HBO Max to further continue the feud between the wisecracking rabbit and the wascally wabbit hunter. The model is meant to be glued.ĭo not hesitate to ask questions, feedback is essential to making better models.Bugs Bunny needs to be extra careful as his longtime nemesis Elmer Fudd is once again packing heat.

As you glue the shirt into the bottom parts, the belt will position itself and fit snugly.ħ - Since the model is top heavy, I glued the bottom of the model to the base and let it set completely before gluing in the head.Ĩ - Refer to the assembly diagrams in the pictures section as well as the uploaded pictures for putting the model together. They should fit easily and almost flush to the eye_whites.Ħ - The belt goes onto the bottom of the shirt without needing glue. This will allow you to adjust it later to ensure it fits perfectly with the Bugs model.ĥ - Be sure to insert the eye_blacks in correctly (left/right are different) and not upside down. You can glue this in, or add a bit of double sided tape to the left scythe_handle where it goes into the left hand. This will also ensure that the gun is positioned correctly when placed against the Bugs model.Ĥ - The optional scythe snaps into the right hand but is not snug enough into the left hand to hold it into position. It should fit in position with just a slight snap. Just remember to leave enough time for the glue to set before combining too many parts.ģ - I glued the gun together but did not glue it to the hands. I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. The sticky glue allows more time to position the parts than a fast drying superglue. I ordered some more filament and the color was identical, as though it came off the same run.ġ - Take your time gluing the model together and enjoy the process.Ģ - I used E6000 sticky craft glue to put this model together. I had some Paramount3D PLA Military Brown from five years ago and ran out while printing this model. So, choose your colors as you see fit.Ĥ - Fun fact. For the smaller parts, a good first layer is helpful.ģ - Looking at Elmer Fudd pictures I found that his colors varied somewhat, especially his gun. When setting up my prints I prefer to be conservative, especially since the base of many parts are hidden when inserted into another part. Only the tips of the ears would need supports.Ģ - There are some pieces that may need brims or rafts, use your discretion. The head is presented with built-in supports as well as an optional piece if you want to use your slicer supports. Green: (Paramount3D PLA - St Andrews Green)ġ - No supports are required.

Head_without_supports (optional piece if you use your slicer supports) Skin: (Paramount3D PLA - Universal Beige) (note: this red is not as bright as other red filament)īrown: (Paramount3D PLA - Military Brown) Refer to the notes below for a few helpful printing and assembly instructions. If you have the proper filament colors, no painting is needed. One piece contains built-in supports, an optional part without the built-in supports is also supplied if you want to use your slicer supports.

Elmer fudd full#

See my Bugs model to complete the full iconic scene with Bugs' finger in Elmers gun (or scythe if you prefer): To honor this change, this model contains an optional scythe that you can use interchangaebly with the gun. In a new short titled 'Dynamite Dance,' Fudd uses a scythe as he chases his nemesis Bugs Bunny. announced that Elmer will no longer have a gun. He speaks in an unusual way, replacing his Rs and Ls with Ws, so he often refers to Bugs Bunny as a 'scwewy' or 'wascawwy (rascally) wabbit'.Įlmer's trademark phrase is 'Shhh. His aim is to hunt Bugs, but he usually ends up seriously injuring himself and other antagonizing characters. Looney Tunes/Merrie Melodies series, and an adversary of Bugs Bunny. Fudd, a fictional cartoon character in the Warner Bros.